Just how to Replace a Bathtub ( Guide).
Just how to Replace a Bathtub ( Guide).
Blog Article
On this page in the next paragraph you can discover a good deal of dependable resources pertaining to Installing A Bathtub.
Setting up a tub isn't precisely brain surgery, however it does need strong plumbing, woodworking, as well as often, tiling skills. Replacing an old tub with a new one is likewise a moderately tough project. If the old tub is readily available, the job can move quickly; if you need to open a wall to eliminate the old tub and position the new bathtub, the job is a lot harder. In either instance, the job is within a home handyman's skills, although you will need an assistant to move out the old tub and also embeded in the brand-new one. Make certain you have actually qualified yourself for the work as well as fit attempting it. Rather than hiring a contractor to take control of a halfway-completed job, it is much better to consider employing one prior to you start. Possibilities are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your washroom if you have actually currently purchased a new tub and do not require to alter the arrangement of your previous water supply pipelines.
Your tools and product list ought to comprise the following:
Planning for the Setup
Firstly, the sustaining framework supplied with the bathroom must be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the restricted accessibility that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of both wooden boards under its feet, put the tub in the needed setting. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub till the level reviews degree.
To mount faucets, fit all-time low of the outermost versatile tap port to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
Activate the supply of water and check all joints and brand-new pipework for leakages and also tighten them if needed. Fill up the tub and also examine the overflow electrical outlet and also the typical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has actually been made use of a minimum of when as this will certainly resolve it into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washing machines remain in location between the faucet and also the sink. Secure the faucet in place with the manufacturer given backnut. When the tap is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The previous type needs to be attached to the tap finishes initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about problems with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your fixtures and also fittings. They are sold in tubes as well as cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to always fill the tub with water before sealing, to allow for the movement experienced when the tub remains in use. The sealant can break relatively early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently available on the market. It is a good idea to fit the floor tiles using water-resistant or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Place feedback below. We would be interested to listen to your reactions about this write-up. We hope that you come back again in the near future. If you please set aside a second to share this write-up if you enjoyed it. Thanks so much for taking the time to read it.
This Website Report this page